SK 2PO = 
1 ?
2 ?
3 Input P4 MAX3243
4 ?
5 Output P10 MAX3243
6 ?
7 ?
8 ?
9 GND


PO J100


Lattice
LC4064V
TQFP100


3COM BASELINE Switch 2824-SFP Plus
3C16487



?Help Menu:

 NG - Get Current Network Settings
 NS - Configure Network
 NM - Configure MAC Address
 GG - Get Switch register
 GS - Set Switch register
 GR - Read MCU register
 GW - Write MCU register
 PG - Get Port Property
 PS - Set Port Property
 YI - Init PHY
 YG - Get PHY MII register
 YS - Set PHY MII register
 YD - Dump PHY MII registers
 YC - PHY Cable Diagnostic

SBCM> ng NG - Get Current Network Settings

MAC=00:18:6E:01:5A:3C
DHCP Client: Disabled
IP: 192.168.1.4
Netmask: 255.255.255.0
Gateway: 192.168.1.1

SBCM> ns NS - Configure Network

Do you want to enable DHCP Client? n
IP: 192.168.1.4
Netmask: 255.255.255.0
Gateway: 192.168.1.1

IP Configuration Completed

SBCM> ?Help Menu:

 NG - Get Current Network Settings
 NS - Configure Network
 NM - Configure MAC Address
 GG - Get Switch register
 GS - Set Switch register
 GR - Read MCU register
 GW - Write MCU register
 PG - Get Port Property
 PS - Set Port Property
 YI - Init PHY
 YG - Get PHY MII register
 YS - Set PHY MII register
 YD - Dump PHY MII registers
 YC - PHY Cable Diagnostic

SBCM> nm NM - Configure MAC Address
Current MAC=00:18:6E:01:5A:3C
New MAC=


SBCM> nm NM - Configure MAC Address
Current MAC=00:18:6E:01:5A:3C
New MAC=


SBCM> gg GG - Get Switch register
 Reg: 0x00

Reg[0000]=00000038

SBCM> gc <-- Invalid command!

SBCM> c <-- Invalid command!

SBCM> g

SBCM> c <-- Invalid command!

SBCM> gc <-- Invalid command!

SBCM> c <-- Invalid command!

SBCM> gg GG - Get Switch register
 Reg: 0xg?

SBCM> gg GG - Get Switch register
 Reg: 0xff

Reg[00FF]=00000000

SBCM> ?Help Menu:

 NG - Get Current Network Settings
 NS - Configure Network
 NM - Configure MAC Address
 GG - Get Switch register
 GS - Set Switch register
 GR - Read MCU register
 GW - Write MCU register
 PG - Get Port Property
 PS - Set Port Property
 YI - Init PHY
 YG - Get PHY MII register
 YS - Set PHY MII register
 YD - Dump PHY MII registers
 YC - PHY Cable Diagnostic

SBCM> g

SBCM> pg PG - Get Port Property
Port number : 0x1

Port 0x 1 is ENABLE !!
Port 0x 1 is autoneg ENABLE !!
Port 0x 1 speed duplex is 100FULL !!
Port 0x 1 is flow control DISABLE !!
Port 0x 1 is link up !!
Port 0x 1 : default port priority is 0x 0 !!

SBCM> pg PG - Get Port Property
Port number : 0x4

Port 0x 4 is ENABLE !!
Port 0x 4 is autoneg ENABLE !!
Port 0x 4 speed duplex is 1000FULL !!
Port 0x 4 is flow control DISABLE !!
Port 0x 4 is link down !!
Port 0x 4 : default port priority is 0x 0 !!

SBCM> ?Help Menu:

 NG - Get Current Network Settings
 NS - Configure Network
 NM - Configure MAC Address
 GG - Get Switch register
 GS - Set Switch register
 GR - Read MCU register
 GW - Write MCU register
 PG - Get Port Property
 PS - Set Port Property
 YI - Init PHY
 YG - Get PHY MII register
 YS - Set PHY MII register
 YD - Dump PHY MII registers
 YC - PHY Cable Diagnostic

SBCM> yi YI - Init PHY
[PHY Init]
Front PortID:0x5

[Init]Port(0x5)'s PHY init finished!

SBCM> yi YI - Init PHY
[PHY Init]
Front PortID:0x9

[Init]Port(0x9)'s PHY init finished!

SBCM> yd YD - Dump PHY MII registers
[PHY Set]
Front PortID: 0x5

[00-07]: 1140 7949 0020 60B1 05E1 0000 0004 2001
[08-0F]: 0000 0600 0000 0000 0000 0000 0000 3000
[10-17]: 0000 0000 0000 0000 0000 0000 0000 0000
[18-1F]: 0400 1000 0000 FFFF 0000 0000 0000 0000

SBCM> yd YD - Dump PHY MII registers
[PHY Set]
Front PortID: 0x1

[00-07]: 1140 7949 0020 60B1 01E1 0000 0004 2001
[08-0F]: 0000 0300 0000 0000 0000 0000 0000 3000
[10-17]: 0000 2000 0000 0000 0000 0000 0000 0000
[18-1F]: 0400 1000 0000 FFFF 0000 0000 0000 0000

SBCM> yd YD - Dump PHY MII registers
[PHY Set]
Front PortID: 0x2

[00-07]: 1140 7949 0020 60B1 05E1 0000 0004 2001
[08-0F]: 0000 0200 0000 0000 0000 0000 0000 3000
[10-17]: 0000 0000 0000 0000 0000 0000 0000 0000
[18-1F]: 0400 1000 0000 FFFF 7C08 0000 0000 0000

SBCM> ?Help Menu:

 NG - Get Current Network Settings
 NS - Configure Network
 NM - Configure MAC Address
 GG - Get Switch register
 GS - Set Switch register
 GR - Read MCU register
 GW - Write MCU register
 PG - Get Port Property
 PS - Set Port Property
 YI - Init PHY
 YG - Get PHY MII register
 YS - Set PHY MII register
 YD - Dump PHY MII registers
 YC - PHY Cable Diagnostic

SBCM>